Equivalent E295 Steel and steel price

Equivalent  E295 Steel and steel price

 E295 steel is equivalent to the domestic Q295A low-alloy high strength steel sheet. German S235JRG2 is a kind of ordinary carbon structural steel, non alloy hot rolled structural steel, which corresponds to the high strength hot rolled steel plate of Q235B steel in China. DIN17440 standard, German standard material, relative to the domestic material S235JRG2 RSt37-2 St 1203 F2 A2-70 1.457110 St 50-2K S355J2G3 E295+C E295 St E295 St50-2 200HV-St Cu St70-2 C35 E295 200HV-St.
 
Equivalent to China's Q235, J represents the shock wave, >27 R represents the indoor temperature of 20 degrees G2, represents the heat treatment delivery status, to negotiate with suppliers.
S355j2g3: low-alloy, high-strength structural steel, Q345, S355J2G3, roughly equivalent to GB Q345DS355J2G3 is the European standard steel, the composition of C = 0.20, Si = 0.55, Mn = 1.60, P = 0.035, S = 0.035. The national standard instead of "Q345D", "J2G3" means that the state of delivery is normalized, the impact work at -20 is 27J, and G3 and G4 are the means of characterizing the deoxidation. S355J2G3 stands for semi killed steel, and S355J2G4 is indicated as fully killed steel.
C25: Germany's average carbon content of 0.25% cast steel, the specific component is:
C 0.22-0.29%
Si = 0.40%
Mn 0.40-0.70%
P = 0.045%
S = 0.045%
Cr = 0.40%
Mo = 0.10%
Ni = 0.40%
 
E295 steel round bar:
Diameter : 1mm-2000mm
E295 steel square bar:
Size: 50mm * 50mm-600mm *600mm
E295 steel plate steel/flat bar:
Size: Thickness: 0.1mm-800mm Width: 10mm to 1500mm
E295 steel tube/pipe: 
Size: OD: 6-219mm WT: 1-35 mm.
E295 steel cold-rolled sheet: Thickness: 2-5mm Width: 1000mm Length: 2000mm
E295 steel hot-rolled sheet: Thickness: 6-80mm Width: 210-610mm
Length: We can supply any length based on the customer's requirement.
Forging/hot rolling/ extrusion of steel.
Forging: Shafts with flanks/pipes/tubes/slugs/donuts/cubes/other shapes
Finished goods condition: hot forging/hot rolling + annealing/normalizing + tempering/quenching + tempering/any conditions based on the customer's requirement
Surface conditions: scaled (hot working finish)/ground/rough machining/fine machining/based on the customer's requirement.
Furnaces for metallurgical processing: electrode arc + LF/VD/VOD/ESR/Vacuum consumable electrode.
Ultrasonic inspection: 100% ultrasonic inspection for any inperfections or based on the customer's requirement.
 
Cold rolling is made of hot rolled coil as raw material and rolled under normal recrystallization temperature at room temperature. Cold rolled steel plate is produced by cold rolling process, referred to as cold plate. The thickness of cold rolled sheet is generally between 0.1--8.0mm. The thickness of cold-rolled steel plate produced by most factories is below 4.5mm. The thickness and width of cold rolled plate are determined according to the equipment capacity and market demand of each plant. Cold rolling is a steel plate that is rolled at the target thickness below the recrystallization temperature at room temperature. Compared with hot rolled steel sheets, cold-rolled steel sheets are more accurate and smooth and beautiful in appearance.
More information about P 295 steel application and introduction, and if you need factory price of P 295 steel stock, contact us at any time. Welcome to call for us. We strive for excellence in quality and meticulous in service. We hope to cooperate with us in the near future.